Specification Sheet: AM 210/x0x
Intel® Core™ 2 Duo Processor
AdvancedMC™ Module
Central Processor
- 2.26 GHz Intel® Core™ 2 Duo processor SP9300 or
1.86 GHz Intel® Core™ 2 Duo processor SL9400:-- using a μFC-BGA 956 (micro Flip-Chip Ball Grid Array) package
- 32 Kbytes of primary (L1) on-die cache
- 6 Mbytes of shared secondary (L2) on-die cache
- 1066 MHz Front Side Bus (FSB)
- Intel® 64 (or Intel® EM64T) 64-bit computing support
- utilizes 64-bit Intel® GS45 and ICH9M-SFF chipset
DRAM
- full-height AMC module supports up to
8 Gbytes DDR3-1066 SDRAM:-
- via two SODIMM sockets
- peak bandwidth of 16 Gbytes/s
- accessible from processor and AMC connector
PICMG® AdvancedMC™ Interfaces
- hot swap compliant to AMC.0
- single x8 or dual x4 PCI Express® fabric connection:-
- AMC.1 Type 8
- transfer rate up to 4 Gbytes/s
- supported by a DMA engine in the PCI Express switch
- can be used as two x4 interfaces in dual redundant fabric systems
- external or on-board fabric clock support
- rear I/O compliant to AMC.1 specification
- can be configured for compliance with the requirements of the SCOPE Alliance
Storage Interfaces
- up to 4 x Serial ATA300 interfaces:-
- AMC.3 Type S2
- optionally two additional interfaces in AMC connector extended options region
- transfer rate up to 300 Mbytes/s
- supports up to 8 Gbytes optional USB 2.0 Flash Drive Module
Ethernet Interfaces
- dual Gigabit Ethernet interfaces via AMC connector:-
- AMC.2 Type E2
- supporting Serdes type 1000BX
- implemented by Intel® 82576EB LAN Controller via x4 PCI Express port
- 1 x front panel 10/100/1000 Mbps interface accessed via RJ45 connector:-
- implemented by an Intel® 82567LM LAN PHY
Firmware Support
- Phoenix® TrustedCore™ Server
- comprehensive Power-On Self-Test (POST)
- LAN boot firmware included
Flash EPROM
- 4 Mbytes of BIOS SPI Flash EPROM
Serial Interfaces
- up to 2 x RS232 serial channels:-
- 1 channel via RJ45 front panel connector
- optionally 1 channel in AMC connector extended options region
- 16550 compatible UART
- modem control signals supported:-
- front channel supports TxD, RxD, CTS, RTS, DSR, DTR and DCD
- rear channel supports TxD, RxD, CTS and RTS only
Other Peripheral Interfaces
- PC-compatible Real Time Clock
- watchdog timer
- 1 x 32-bit Long Duration Timer with processor interrupt capability
- CPU temperature monitor; voltages monitor:-
- all accessible via IPMI
- up to 5 x USB 2.0 (Universal Serial Bus) interfaces:-
- 2 channel via front panel
- optionally 2 channels in AMC connector extended options region
- 1 channel supports optional USB Flash Drive Module
Software Support
- support for Linux®, Windows® Server 2003, Windows® Server 2008, Windows® XP, Windows® XP Embedded, QNX® and VxWorks®
IPMI
- IPMI Version 1.5 according to AMC.0
- on-board BMC (Baseboard Management Controller)
- supports 8 Kbytes of non-volatile memory
Electrical Specification
- +12V @ 3.2A (typical at 2.26 GHz with 8 Gbytes SDRAM), voltage ±2V
- +3.3V @ less than 0.15A, voltage ±5%
Safety
- PCB (PWB) manufactured with flammability rating of 94V-0
Environmental Specification
- operating temperature:-
- 0°C to +55°C (N-Series, all configurations)
- -25°C to +70°C (E-Series, 1.86 GHz, full-height front panel. 2.26 GHz full-height front panel)
- -40°C to +85°C (storage)
- 5% to 95% Relative Humidity, non-condensing (operating and storage)
Mechanical Specification
- AMC.0 single-width form-factor:
180.6mm x 73.5mm (7.1 inches x 2.9 inches) - full-height panel: 29mm (1.1 inches):-
- mid-height version available