TP 402/35x - Intel Core 2 Duo Processor 3U SBC

Specification Sheet: TP 402/35x

Intel® Core™ 2 Duo Processor 3U SBC

(click to view Ruggedized Air-Cooled or Ruggedized Conduction-Cooled)

Central Processor

1.06 GHz Intel® Core™ 2 Duo Processor U7500 or
1.5 GHz Intel Core 2 Duo processor L7400:-
- using a µFC-BGA 478 (micro Flip-Chip Ball Grid Array) package
- 64 Kbytes of primary (L1) on-die cache
- 4 Mbytes of shared secondary (L2) on-die cache
- 667 MHz Front Side Bus (FSB)
- Intel® 64 Technology (64-bit computing)
utilizes 64-bit Intel® 3100 server chipset:-
- single chip chipset with integrated memory and I/O controllers
provision for ITP debug port

DRAM

2 or 4 Gbytes soldered DDR2-400 registered ECC SDRAM using:-
- single channel memory
- single-bit error correction
- peak bandwidth of up to 3.2 Gbytes/s
accessible from processor or CompactPCI® bus

Hard/Flash Disk Interfaces

Serial ATA150 interfaces:-
- transfer rate up to 150 Mbytes/s
2 x channels accessible via J2
1 x channel routed to on-board 512 Mbytes Flash disk
2 x channels routed to optional Flash Disk Module:-
- one or two Flash disk drives
- appear as one or two hard disk drives
- uses XMC connectors (see Note 1)

Ethernet Interfaces

2 x channels supporting:-
- 10 Base-T, 100 Base-TX, 1000 Base-T
- implemented by Intel® 82571EB via x4 PCI Express® port
- both channels accessed via J2

Optional Graphics Interface

optional PMC card mounted on 3U CompactPCI PMC carrier:-
- see separate IO PMC/722 and TP CRx/PMC datasheets
for IO PMC/722:-
- implemented by Silicon Motion SM722
- analog and digital graphics accessed via front panel DVI-I connector or PMC rear I/O
- 8 Mbytes video memory
- resolutions up to 1280 x 1024; supporting up to 16M colors

Serial Interfaces

2 serial interfaces accessible via J2
1 x RS232 interface supporting Tx and Rx
1 x RS232 interface supporting Tx, Rx, RI, CTS, RTS, DSR, DTR and DCD or 1 x RS422/485 supporting Tx and Rx
16550 compatible UARTs

Flash EPROM

1 Mbyte of BIOS Flash EPROM
hardware write protect provided

Firmware Support

Phoenix™ TrustedCore BIOS
Trusted Platform Module (TPM) support
comprehensive Power-On Self-Test (POST)
LAN boot firmware included

Software Support

supports Linux®, Windows® XP, Windows® XP Embedded, Windows® 2000, Windows® Server 2003, QNX®, LynxOS® and VxWorks®

Other Peripheral Interfaces

PC-compatible Real Time Clock (Year 2000 compliant)
long duration timer
watchdog timer
legacy speaker interface
2 x USB 2.0 interfaces:-
- both accessed via J2
external battery supply for RTC and BIOS data
4 x GPIO signals via J2
on-board I2C bus used for local temperature and power supply sensors, accessible via J1

CompactPCI Interface

universal signaling support, compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels
33/66 MHz; 32-bit interface accessed via J1
utilizing a PCI Express-PCI bridge for off-board accesses
operates as a System Slot controller (supporting up to 7 Peripheral Slots) or operates in a Peripheral Slot:-
- supports hot-swapping peripheral boards
- PICMG 2.1 R2.0 Hot Swap Specification
option to disable CompactPCI interface (Satellite Mode):-
- receives power from CompactPCI bus
- board can be hot swapped

Electrical Specification

+5V @ 3.1A (typical 1.5 GHz with 1Gbyte DRAM)
+3.3V @ 3.7A (typical with 1Gbyte DRAM)
+12V and -12V not required
all voltages are tolerant to ±5%

Safety

PCB (PWB) manufactured with flammability rating of 94V-0

Environmental Specification

operating temperatures:-
- 0°C to +55°C (N-Series)
- -25°C to +70°C (E-Series)
- -40°C to +85°C (K-Series)
storage temperature: -40°C to +85°C
5% to 95% Relative Humidity, non condensing (operating or storage):-
- K-Series includes humidity sealant
ruggedized air-cooled version:-
- rear plug compatible
- see TP 402/35x-RA datasheet
ruggedized conduction-cooled version:-
- rear plug compatible
- see TP 402/35x-RC datasheet

Mechanical Specification

3U form-factor: 3.9 inches x 6.3 inches (100mm x 160mm)
single slot
connectors: IEC-1076-4-101 for J1-J2
shock: 20g, 11ms, ½ sine
vibration: 5Hz-2000Hz at 2g, 0.38mm peak displacement

Note 1: The XMC connectors are provided for the SATA Flash Disk Module only. The CPU heatsink for air-cooled boards does not allow an XMC module. The conduction-cooled board does support an optional XMC module (see the TP 402/35x-RC datasheet).